Motorcycle Rear Wheel Not Spinning Freely

September 29, 2021 Post a Comment

You can check if it is the brake or not by loosening the caliper and spinning the wheel. Since the last time the rear wheel was removed somethings not been 100 correct.

How To Install A Dirt Bike Rear Wheel Youtube

It should be easy to fix or they should replace it.

Motorcycle rear wheel not spinning freely. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Joined Jul 23 2010 443 Posts. Rear wheel doesnt spin freely How easily should the rear wheel spin when up on a rear stand.

I hear a faint grinding noise when the wheel spins which I suspect is the brake pads touching the disc. It the back wheel moves forward freely but backwards is a problem then try the pedals by hand with the rear wheel off the ground. See if the wheel spins freely now.

Hey guys I have a question about my wheels. I have problem with my new to me1974 HONDA CB350 Motorcycle bike. If it spins freely it is the brake not the hub.

Seems to do better after I have ridden the bike. When i tighten the axle nut to spec the rear wheel is not spinning freely like it used to. Rear wheel not spinning freely.

Jump to Latest Follow REVIEWS DEALS BIKESHOPS TRAILS. When the right 27mm axle nut is torqued down theres so much friction I can hardly spin the rear wheel with the bike on the centerstand. I continued to spin my rear wheel and still it did not spin freely.

So I was lubing the chain on my Ninja 250R today and noticed that the rear wheel did not spin as freely as I remembered. If I take the wheel off and spin it on the axle it spins like it is supposed to. I noticed this weekend that it takes a bit of pressure to turn the rear wheel.

I recently ran over a nail and needed a new tire. Dont disconnect the hydraulic line but arrange some support for the caliper so that it isnt strained. 1 - 8 of 8 Posts.

Discussion Starter 1 Sep 26 2010. I am used to my R6 that when it was on a stand i could spin it and it would go forever. Any advice is appreciated.

If thats not the problem remove your rear brake caliper from the swinging arm. Any ideas on what is causing my problem. Theres a freewheel and at least two additional bearings in the rear wheel all of which add drag.

In neutral the rear wheel spins freely in the forward direction but if I try to spin in reverse direction it either does not spin is hard to spin or spins briefly and stops abruptly. I am not sure what it could be. First If I torque the rear axle nut to 47lbft it will not spin very freely at all.

When the bike is in gear and the clutch lever is released the clutch is engaged and the rear wheel is powered by the engine so it shouldnt spin freely it should spin as fast as the throttle makes it go. I own a Yamaha MT15 which has. Bottom bracket is too tight.

Test as tlg suggested wheel off the bike turn the axle by hand. Any input would be greatly appreciated. I replaced with my old stock wheels for a comparison and they continued spinning for well over a minute before I stopped them.

It seems like its in the motor that is. Now that it is back on something isnt right. If it stiff or rough at all then theres a problem.

I have checked rear brake it is not interfering with it. I just got my tire changed and had pulled the rear wheel off. I got the wheel off fine but when replacing the wheel two things have me a little unsure.

Even with a hard spin it would struggle to turn 360 degrees. I was cleaning the rims and the weheel doesnt spin to freely. I recently took apart the hubs and put grease on all bearings.

If it is the hub you might need to get it regreased. The rear will never spin as freely as the front. I go to put the wheel back on the bike to true the wheel and it hardly spins.

No way can I torque the nut to the recommended 69ftlbs the wheel would then barely spin. I then replaced with the new wheel again and continued to spin it and I have noticed a slight improvement but still nowhere near the old wheel. Through it might have been a tight axle nut or rear pads but nope neither of those.

I think anything else would be abnormal. Im new to this community and Im a noob in terms of knowledge about motorcycles so please ignore my ignorance. Once you have identified the problem take it back to where you got it.

If this doesnt turn freely the pedal crank bearing aka. Alternatively it might just be overtightened although its not likely to tighten by itself in the shed. If I back it off to about 38-39 or so it will feel tight but spin freely as it should.

I just put in new brake fluid and bled the brakes so it could just be the brakes but what are the symtpoms af bad bearings or any other. Check that the wheel isnt touching the ground first and that you are in neutral.

Simple Steps To Check Wheel Alignment In A Motorcycle